・Rear 160-180 tires can be used ・Chain line value: 100-105mm *When stretching the chain, make sure there is adequate space between the roller and the rear sprocket. *Please use the supplied collar according to the tire size. *The installation of the product must be carried out correctly by a mechanic with knowledge and skills. Repair parts are here.
If the angle of the swingarm is tighter, the amount of space of the drive chain needs to be larger than before. As the swingarm strokes, the rear axle point becomes farther and farther away, and if the chain space is small, it can lead to the case of over tension and lock in the worst case. However, when the chain space is set to the minimum, the disadvantage of the large amount of slack (vibration of the power transmission system during acceleration and deceleration) becomes more noticeable and may have a negative effect on the handling during sudden braking and acceleration. SANCTUARY MECHANIC BRAND Drive Chain Roller Slider is designed to put the roller close to the swingarm pivot for effective tensioning of the drive chain. This item not only adjusts the space of the drive chain at the bottom of the pivot, but also prevents the interference between the drive chain and the frame that occurs as the rear wheel becomes wider. By using different spacers and shims, various chain line offset values can be accommodated.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I installed the Drive chain roller slider for the first time. I introduced it because the Bolt on the back of the footpeg interferes in two places (17Inch?). It's a Bolt On product because it has a Knight's Down tube and Rear Sets. (I heard that this tightness is a manufacturer's standard. I hear it gets better the next time. If you are a first time buyer, please refer to this page. When the Roller is shaved, Red powder is naturally produced.View Detail
The same goods purchased those with three company, and made in [ including Nitro / which are likely to have intensity most in it ] Nitro in the volume retailer.It was the atmosphere which the other 2 company had thin thickness and form of the stay part where a Guide roller is specifically attached, or processed the several millimeters aluminum board.Although it was cheap about thousands of yen in price, since it was a portion which always contacts a Chain when running, made in [ which is likely to be excellent in intensity ] Nitro was chosen. Anodized processing is also carried out and texture and functionality are places called an expected passage.Since Pons attachment cannot be performed unless a Side stands sensor removes, it is attaching by removing.At the time of departure, it is a check required about a STAND. I have equipped with the Wheel of 5.5 pieces and have offset the Chain line 8 mm again.I think that it was good in that there are some spans of adjustable range since it was touch that the Chain was just before the outside of a Guide roller.it is satisfactory if Wheel width is 5.5 or less -- it is -- although -- some processings are likely to be needed if it is more than this.Although it is a Side stands stopper, it has interfered in the last splendidly.It is coped with for the time being using the Stay of L character which is sold at the Home center for this reason.Since there seems to be no problem for the moment although it is in this state one month or more, I would like to cope with it gradually.View Detail
Although the quality of a fixing system or a Roller came out strongly and was very well, if it did not cut whether the attachment part of a Side stands sensor would be bent, the big issue which is not attached and made generated it.Attachment was given up tearfully.it is because it runs with STAND appearance carried out and there is a danger electrical of an accident.Please sell the transfer Bolt on parts of a Side stands sensor.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!