The quality of the product is good, it is genuine, and the packaging is safe and rigorous! After paying for the order, the goods will be received within a week and sent to the office, which is very fast and convenient!
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
The quality of the product is good, it is genuine, and the packaging is safe and rigorous! After paying for the order, the goods will be received within a week and sent to the office, which is very fast and convenient!
It was a Type 3 Grom, so it might have been like Title, but it could be a possible problem. By the way, Blinker and Position are separate LEDs. I'm not sure if it's a problem or not, but I'm not sure if it's a problem or not. So I asked the motorcycle shop to copy the wiring diagram and looked at it. First, I used the rectifier.
Countermeasures?
Add a 6ADiode between both BlinkerWiring and ConnectorWiring.
In addition, the position was extended from the license lamp on the rear and connected, and this extension was large. At this time, in consideration of later, I passed two wires for Earth and two wires for Position.:It is a connection with the License Wiring that has been extended from 2pc to 1pc.
Result?
When I started the engine and started the blinker, it flowed, but it was unstable, coming on and off.
Countermeasures?
No more Blinker around. (Inside Headlight) I heard that it is difficult to add diodes to the 3PHarness. So I went to Mr. Takekawa's place and found a 3PHarness for Honda with universal diodes, which was expensive but I bought it. I used this only for BlinkerWiring.
Result?
Naturally? The result was the same as the previous one.
Countermeasure? This is a countermeasure? Implement immediately after
If this happens, I will add a diode to Blinker's Grounding Wire.
This uses the remaining 1 pc from the extension of Position. The connection was treated in the same way as Position.
Result?
I'm not sure if this is a good idea or not, but I think it's a good idea.
operation
WhitePosition, always on
Blinker, the other side of the stream is still lit up.
Blinker position, always on
I think the light intensity is bright. The light intensity is bright.
As for durability, I think the LED is large and durable, but we'll see.
General review
I chose this blinker because the position will be lost when I install the switch assembly with Hazard later. I'm sure the size and construction is solid. The base is rubber type to prevent vibration.
I'm not sure if it's a test or not. I'm not sure if I'd recommend it, but I'm personally satisfied with it. I'm not sure if I'd recommend it, but I'm personally satisfied. (Maybe because it worked fine.)
I also wish there was a Smoked lens in the lineup.View Detail
The blinker, tail lamp and stop lamp are all in one.
I did a lighting test and it was pretty bright.
Lighting test = check as there is no instruction manual
Black=Earth
Red = Stop
Green Light = Blinker
White=Tail lamp
It was
Reason for replacement = Since I have a top case installed, I thought visibility would be poor in the NORMAL state and decided to replace it.
Simultaneously for Front (with position lamp) I've also bought a new one to make it even safer. (=^・^=)
Wiring is a hassle, but safety comes first.
I'm not sure if this is a good idea or not, but it's a good idea.View Detail
Fits: YAMAHA BW'S R Type 2 Taiwanese specs [2JS] 6 term *5 term requires wiring modification., YAMAHA BW'S 125 Model 2 domestic specs [BG12-] SED9J- *[BG11] SEA6J requires wiring modification.
Harness for Blinker flashing can be installed, but put between Night lightWiring for always on.
The included Night Light harness could not be installed because the Coupler is different.
Wiring is processed and used.View Detail
Fits: YAMAHA BWS125(BWS) BWS R 2JS, YAMAHA BWS125(BWS) BWS R 2JS, YAMAHA BWS125(BWS) Type 2 BG1
Because the Front Blinker was very good, I changed the Rear Blinker to the same type. The brightness is brighter and brighter than OEM.
PS
The OEMBlinker was replaced with LED as a balls-up, but it's brighter than that, so I think it's pretty bright.View Detail
Fits: YAMAHA BW'S 125 Model 2 domestic specification [BG1]., YAMAHA BW'S R Type 2 Taiwanese specification [2JS] (*with the included special harness)
This is the best design and size for the OEM parts.
The brightness of the Blinker is also much brighter than the NORMAL, and because it is sequential, it is also parenthesis proof when operating. As for the installation, the connector of Blinker is not found, and the Wiring of NORMAL is processed and converted at the back of Cover. Because the power supply Connector had already used the power supply Connector with the extraction of the power supply for the smart phone, the one which was bundled is not used.
The installation took about an hour but it took me a while to find the Connector but if I had machined the existing Wiring from the start it would have taken about 20 minutes.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Customer Service
INFORMATION
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING