Less choice carburetorSpec. It is an exhaust system for GRASS TRACKER.
Since making is good, there was no exhaust leakage from the intermediate Joint, and installation was completed in a short time. Large I'm satisfied..
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Less choice carburetorSpec. It is an exhaust system for GRASS TRACKER.
Since making is good, there was no exhaust leakage from the intermediate Joint, and installation was completed in a short time. Large I'm satisfied..
Fits: HONDA FTR223 MC34, HONDA FTR223 D MC34
found some instructional videos on yourtube then did it myself.instant increase of horse power !louder exhaust means other car drivers take notice. safety first !note 1: make sure you also buy a new exhaust gasket for installation or you will lose horse power.note 2: the set comes with 5 disks. you can tune the exhaust by adding or taking away disk. in my case, the disks turn black meaning it was burning too much fuel in lower gear and i am losing power in the higher gear. all i have to do is to add 1 or 2 disks. the disk is now in a coffee color, which means it is working perfectly now.View Detail
Fits: YAMAHA SR400 2H6, YAMAHA SR400 1JR, YAMAHA SR400 RH01J, YAMAHA SR500 2J2, YAMAHA SR500 1JN
Sounds good fuel economy, ride distance ... very well ... I was not disappointed purchased ... Now my friends I was going to order another ... Thank you.View Detail
Fits: SUZUKI ST250 (NJ4CA|Injection)
This is a full exhaust system, consisting of the header pipe as well as the muffler. Both are stainless steel. There is no catalytic converter.The exhaust pipe has a port for the lambda probe oxygen sensor, and has an in-built baffle just before the end where the muffler mounts. The TU250x/ST250 both like a bit of back-pressure to help open the exhaust valve, and I believe that\'s what the baffle is there to help provide, as well as to keep the volume down.The muffler itself is very lightweight, has no packing, and just has a minor cage on the interior. The sound is good (not overly loud), and the look is great. It mounts to the existing pillion footrest bracket without any issue. I found that it fit better on the inside of the bracket, contrary to the image of this muffler mounted on the Grasstracker model.I noticed that it seems to give off more heat, so I\'m considering wrapping mine -- it started going blue-gold at the exhaust port on the very first ride. Other than that, I\'m happy with it.View Detail
Fits: KAWASAKI ESTRELLA RS BJ250A[Fitting and other information]Carburetor model, KAWASAKI ESTRELLA Custom BJ250A[Fitting and other information]Carburetor model, KAWASAKI ESTRELLA RSCustom BJ250A[Fitting and other information]Carburetor model, KAWASAKI ESTRELLA BJ250A[Fitting and other information]Carburetor model
I used to ride an ESTRELLA.
It was on a body I bought used.
Dirt track was popular at the time.
Personally, I have the impression that it is not compatible with Engine characteristics.
If you have a 250cc motorcycle, you will be able to get more power and higher rpm, so you will lose the idyllic trotting impression of the ESTRELLA.
good point
If you replace the filter and carburetor, you can get more power.
For Super trap4Inch, you can use Large half.
A bad point
The sound becomes a continuous sound.
Carburetor setting is difficult, AfterFire appears, if no setting.
I guess it's a matter of taste, but I don't think an exhaust system that doesn't fit the nature of a motorcycle is the way to go.View Detail
[How is it used?
I installed it on my 2010 CB223S.
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
The handwritten Punch picture was included in the package, so I could install it while looking at it.
It was very easy to install.
Gasket was described as reuse, but just in case for ReplacementGasket.
I had purchased it and installed that.
How was your experience with it?
Sound is satisfying Large, even if you wear a full face helmet, your own
Exhaust SystemSound can now be heard.
[Included Parts:were they on?
It was attached and not loose.
[Was there anything that disappointed you?
It's not a disappointment, but it's a bit like a thinner, slower Torque.
I felt it, but it's not a complaint Level.
On the other hand, I'd like to check it at high speed.View Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Customer Service
INFORMATION
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING